Repair ABS Sumitomo Isuzu Series N
- DiPa Code:
- ABS2423R
- OEM Code:
- 2064543
- Brand:
- DIPA SPORT
- Cod.Cross:
- Condition:
- Remanufactured
Warnings
Send the spare partWITHOUT SUPPORTSandSCREWSattached, we will not be held responsible in case of breakage or loss of the same.
The indicated cost represents the average revision cost for this type of spare part.
The final quote will be formalizedin writingafter evaluation and possible acceptance by the technical department, based on the faults specifically reported in the repair request.
Note Wellthe quote you will receive refersonlyto the defects indicated in the initial request, DIPA will carry out the revision interventionexclusivelyon the reported faults.
In case anyfurther issuesarise during processing, DIPA will promptly inform you, specifying any changes to theprocessing timesand to thequoted amount. Only after yourwritten approvalof such changes will we proceed with the completion of the repair.
Typical Errors and Defects
Typical Defects:
One or more wheels do not brake, no brake fluid reaches the calipers
One or more wheels remain locked
The brake pedal sinks
No communication between abs and diagnostic system, does not detect speed on the instrument panel
Applications
ISUZU
ISUZU N (5th Generation)
| Model | Year of Production | Displacement | KW | HP | Cylinders | Fuel Type | Engine Code |
|---|---|---|---|---|---|---|---|
| N (5th Generation) | 2005-01-01 - 2009-12-01 | 5193 cc | 109 KW | 148 HP | Cylinders | ||
| N (5th Generation) | 2005-10-01 - | 5193 cc | 110 KW | 150 HP | Cylinders | ||
| N (5th Generation) | 2005-10-01 - | 5193 cc | 117 KW | 159 HP | Cylinders | ||
| N (5th Generation) | 2008-09-01 - | 5193 cc | 110 KW | 150 HP | Cylinders |
Techinical Info
The OE code 898000570 identifies the ABS module used on Isuzu N-series light commercial vehicles. It is the complete assembly because it integrates the electronic control unit and the hydraulic modulator assembly (internal valves + electric recirculation/pressure reapplication pump) into a single unit.
Technical specifications
- Type: EHCU (Electronic Hydraulic Control Unit)
- Function: hydraulic modulation of brake pressure to prevent wheel lock
- Architecture: hydraulic unit with inlet/outlet solenoid valves for the brake circuits and an electric pump (motor) for pressure management during ABS intervention
DIPA can intervene to overhaul these components thanks to its experience and expertise.
Functionality
- ABS control during braking: detects the risk of wheel lock via wheel speed sensors and commands the modulator to: reduce pressure on the affected circuit; maintain and restore pressure cyclically.
- Self-diagnosis: continuous monitoring of power supplies, grounds, sensor circuits and actuator circuits (pump and solenoids).
- Diagnostic interface: read/clear faults and perform test procedures with a diagnostic tool (depending on the system version).
Make and model on which the part is mounted
- Isuzu N
Common faults
- One or more wheels do not brake; brake fluid does not reach the calipers
- One or more wheels remain locked
- Brake pedal sinks (loss of pedal firmness)
- No communication between the ABS and the diagnostic system; speed not detected on the instrument cluster
Final conclusions
The Isuzu code 898000570 identifies a complete ABS module: electronic control unit and hydraulic assembly with pump and valves, typical of the Isuzu N-Series.
DIPA has a wide range of spare parts dedicated to the Truck sector, construction vehicles and industrial equipment. In addition, it offers reconditioned components with performance equivalent to new, allowing cost savings on replacements and contributing to environmental protection through the circular economy. If the part you need is not available, don’t worry: DIPA can recondition your part on demand, restoring full functionality and safety in a short time.